Special Design Solution: Pharmaceutical company wanted to replace repetitive manual operation turning over glass bottles/vials with automatic operation.

• This ergonomic flipper table will clamp, lift and rotate trays of vials and/or glass containers.

• Eliminates repetitive motion disorders such as Carpal Tunnel Syndrome.
• Pneumatically controlled for a precise and complete rotation cycle.
• Constructed of “buffed” 316L stainless steel.
• All welds and fittings are free of inclusions.
• Clamping pads are FDA approved.
• All push buttons are protected from wash down procedures.
• The operator must maintain two hands on the push buttons, which are ergonomically placed on the control panel, to progress through it’s cycle.
• An E-Stop, (emergency stop button), is incorporated for a fail safe operation.
• The unit uses “shop” air; eliminating the need for electrical components and all air exhaust is vented outside the room.

This special adaptation of the minVac allows for loading and positioning of boxes.

It has all the standard features of the MinVac.

Our new rigid system is an addition to the airOlift product line. This system incorporates a special “Heavy Duty Four Point Radial Contact Bearing” top swivel and side linear bearings for extra support. This Rigid manipulator has all of the benefits of a regular airOlift such as light weight and lower cost, but is completely rigid. The Powered Extended Reach can be a benefit for those difficult areas with no overhead clearance. Could something like this fit your applications?

• Lifts and rotates signature bundles for printing industry.
• Low air consumption provides low operating costs
• The rotation can be manual or pneumatically controlled.
• Highly productive due to single hanging point on any workstation crane.
• Allows for various bundle sizes.
• Capacities to 500 lbs. (higher capacities as an option).
• Balancers will not lift more than the rated capacity increasing operator safety and confidence.
• Standard lifting heights from 28″ to 117″, depending on capacity.
• Full 360° rotation to eliminate tangled hoses (optional rotating handle).
• Utilizes “shop air”, no need for separate vacuum pumps to maintain.
• The unit will not drop a load due to catastrophic air loss protection.
• Ergonomically designed controls to increase operator productivity.
• Stainless steel and anodized aluminum construction.
• Vacuum indicator and gauge is located in the operator’s view at all times to maintain operator confidence.
• Low dB levels eliminating excess noise pollution.
• Numerous other clamping and vacuum options available.

• Lifts and rotates panels for the Furniture, Electronics, Glass and various other industries.
• The rotation is intermittent for precise positioning to 180°.
• Highly productive due to single hanging point.
• Allows for off-center loading.
• Capacities to 350 lbs.
• Standard lifting heights to 60″.
• Full 360° rotation to eliminate tangled hoses.
• Air logic controls are housed in a protective enclosure.
• Utilizes “shop” air.
• The unit will not drop a load due to catastrophic air loss protection.
• Ergonomically designed controls to increase operator productivity.
• Stainless steel and anodized aluminum construction.
• Vacuum indicator and gauge is located in the operators view at all times to maintain operator confidence.
• Low dB levels eliminating excess noise pollution.
• Numerous other manipulation options available.

This unit was designed to pneumatically clamp a “heated” glass crucible with a capacity of 120 lbs. The attachment has a 16″ clamping range, the arms are shielded and the pads are heat resistant to protect from a maximum temperature of 1000°F. No rotation is needed. Our standard handle is included. Could something like this fit your applications?

This unit was designed to utilize one vacuum cup to attach to a glass crucible with a capacity of 150lbs. The attachment has a 16″ clamping range, the arms are shielded and the pads are heat resistant to protect from a maximum temperature of 1000°F. An easy to use handle is used for manual rotation. A small control handle is included. Could something like this fit your applications?

This unit was designed for a company that reconditions computer monitors. The airOlift has 250 lbs maximum capacity, off-center loading and 59″ of vertical lift available. The attachment incorporates a 90° upender and a 360° manual swivel at the cup (with locks), for proper product orientation and inspection. The sequence of operation is to pick the monitor up (by screen), from a “cut” box, rotate for inspection and proper orientation then place on work table. An ergonomic control handle is included. Could something like this fit your applications?