AiroLift™ with heavy-duty 90° Upender and adjustable spreader bar
AiroLift™ with Cheese Barrel Rotator
AiroLift™ with Cheese/Box Extractor Attachment
AiroLift™ with 90° Upender and 360° Swivel at cup
AiroLift™ with Vacuum/Clamping Attachment
AiroLift™ with a Special Clamping Attachment
AiroLift™ Rigid Manipulator
AiroLift™ Drum Lift with Manual Rotate
AiroLift™ with 90° Upender and 360° Swivel at cup
AiroLift™ with Vacuum Attachment & Manual Rotation – Heat Resistant
AiroLift™ Heat Resistant Clamping Attachment
AiroLift™ with 180° Panel Inverter
AiroLift™ Signature Bundle Clamping Fixture
AiroLift™ Rigid Manipulator on Articulating Jib Crane With Powered Extended Reach
MinVac™ Low Profile Box Lifter – “Spider Lift” series
AiroLift™ 750 lb Paper Roll Inverter
Free-Standing Tray Flipper
Free-standing tray flipper
Special Design Solution: Pharmaceutical company wanted to replace repetitive manual operation turning over glass bottles/vials with automatic operation.
- This ergonomic flipper table will clamp, lift and rotate trays of vials and/or glass containers.
- Eliminates repetitive motion disorders such as Carpal Tunnel Syndrome.
- Pneumatically controlled for a precise and complete rotation cycle.
- Constructed of “buffed” 316L stainless steel.
- All welds and fittings are free of inclusions.
- Clamping pads are FDA approved.
- All push buttons are protected from wash down procedures.
- The operator must maintain two hands on the push buttons, which are ergonomically placed on the control panel, to progress through it’s cycle.
- An E-Stop, (emergency stop button), is incorporated for a fail safe operation.
- The unit uses “shop” air; eliminating the need for electrical components and all air exhaust is vented outside the room.
AiroLift™ 750 lb Paper Roll Inverter
MinVac™ Low Profile Box Lifter – “Spider Lift” series
AiroLift™ rigid manipulator on articulating jib crane with powered extended reach
Our new rigid system is an addition to the airOlift product line. This system incorporates a special “Heavy Duty Four Point Radial Contact Bearing” top swivel and side linear bearings for extra support. This Rigid manipulator has all of the benefits of a regular airOlift such as light weight and lower cost, but is completely rigid. The Powered Extended Reach can be a benefit for those difficult areas with no overhead clearance. Could something like this fit your applications?
AiroLift™ signature bundle clamping fixture
- Lifts and rotates signature bundles for printing industry.
- Low air consumption provides low operating costs
- The rotation can be manual or pneumatically controlled.
- Highly productive due to single hanging point on any workstation crane.
- Allows for various bundle sizes.
- Capacities to 500 lbs. (higher capacities as an option).
- Balancers will not lift more than the rated capacity increasing operator safety and confidence.
- Standard lifting heights from 28″ to 117″, depending on capacity.
- Full 360° rotation to eliminate tangled hoses (optional rotating handle).
- Utilizes “shop air”, no need for separate vacuum pumps to maintain.
- The unit will not drop a load due to catastrophic air loss protection.
- Ergonomically designed controls to increase operator productivity.
- Stainless steel and anodized aluminum construction.
- Vacuum indicator and gauge is located in the operator’s view at all times to maintain operator confidence.
- Low dB levels eliminating excess noise pollution.
- Numerous other clamping and vacuum options available.
AiroLift™ with 180° panel inverter
- Lifts and rotates panels for the Furniture, Electronics, Glass and various other industries.
- The rotation is intermittent for precise positioning to 180°.
- Highly productive due to single hanging point.
- Allows for off-center loading.
- Capacities to 350 lbs.
- Standard lifting heights to 60″.
- Full 360° rotation to eliminate tangled hoses.
- Air logic controls are housed in a protective enclosure.
- Utilizes “shop” air.
- The unit will not drop a load due to catastrophic air loss protection.
- Ergonomically designed controls to increase operator productivity.
- Stainless steel and anodized aluminum construction.
- Vacuum indicator and gauge is located in the operators view at all times to maintain operator confidence.
- Low dB levels eliminating excess noise pollution.
- Numerous other manipulation options available.
AiroLift™ Heat Resistant Clamping Attachment
This unit was designed to pneumatically clamp a “heated” glass crucible with a capacity of 120 lbs. The attachment has a 16″ clamping range, the arms are shielded and the pads are heat resistant to protect from a maximum temperature of 1000°F. No rotation is needed. Our standard handle is included. Could something like this fit your applications?
AiroLift™ with Vacuum Attachment & Manual Rotation – Heat Resistant
This unit was designed to utilize one vacuum cup to attach to a glass crucible with a capacity of 150lbs. The attachment has a 16″ clamping range, the arms are shielded and the pads are heat resistant to protect from a maximum temperature of 1000°F. An easy to use handle is used for manual rotation. A small control handle is included. Could something like this fit your applications?
AiroLift™ with 90° Upender and 360° Swivel at cup
This unit was designed for a company that reconditions computer monitors. The airOlift has 250 lbs maximum capacity, off-center loading and 59″ of vertical lift available. The attachment incorporates a 90° upender and a 360° manual swivel at the cup (with locks), for proper product orientation and inspection. The sequence of operation is to pick the monitor up (by screen), from a “cut” box, rotate for inspection and proper orientation then place on work table. An ergonomic control handle is included. Could something like this fit your applications?